Luthienstar Networks Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== ResetMaster ======

===== EEPROM Content =====

  * hostname (17 bytes)
  * mac address (6 bytes)
  * listen port (1 byte)
  * confreg (1 byte)
  * ip (4 bytes)
  * subnet (4 bytes)
  * gateway (4 bytes)
  * password (25 bytes)
  * channel_type (1 byte)
  * channel_stat (1 byte)
  * label_1	(17 bytes)
  * label_2	(17 bytes)
  * label_3	(17 bytes)
  * label_4	(17 bytes)
  * label_5	(17 bytes)

===== Configuration registry =====

<code>
[ x x x x  x x x x ]
           | | | \-  Use DHCP
           | | \---  Require passsword
           | \-----  Use CRAM-MD5 instead of cleartext password auth
           \-------  Bufferized channels (avoid toggle during reset)
</code>
===== Port config registry =====

Types:
  * 0: Disabled
  * 1: Bistable
  * 2: Normally open
  * 3: Normally closed

Registry content:
<code>
[ na na na na na na 5h 5l ] [ 4h 4l 3h 3l 2h 2l 1h 1l ]
</code>

===== Port status registry =====
This register is used to save the status of bistable channels.
The value isn't taken in consideration for normally open or normally closed channels.


===== Commands =====
	
  * show channels
  * show running-config
  * show startup-config
  * toggle channel <#>
  * configure
  * reload
  * write

==== show channels ====

Displays channels status

Output:

<code>
Channel 1 [XXXXXXXXXXXXXXXX] (toggle): high
Channel 2 [XXXXXXXXXXXXXXXX] (toggle): low
Channel 3 [XXXXXXXXXXXXXXXX] (toggle): high
Channel 4 [XXXXXXXXXXXXXXXX] (Normally open)
Channel 5 [XXXXXXXXXXXXXXXX] (Normally closed)
Channel 6 [XXXXXXXXXXXXXXXX] (Normally closed)
Channel 7 [XXXXXXXXXXXXXXXX] (Normally closed)
Channel 8 [XXXXXXXXXXXXXXXX] (Normally closed)
</code>

==== show running-config ====
Displays the running configuration.

==== show startup-config ====
Displays the startup configuration.

==== toggle channel ====
Toggles the channel state.

If the channel is bi-stable, the channel will be kept in the current state until the channel is toggled again. Otherwise, the channel will be toggled into the active state (closed for a normally opened, opened for a normally closed) for 1 second.

==== configure ====
Enter into configuration mode

==== reload ====
Performs a self reset. User will be asked to confirm this action.

==== write ====
Writes the running configuration into the startup configuration.

===== Configuration =====
<code>
!
network
  dhcp no
  ip 192.168.1.15
  netmask 255.255.255.0
  gateway 192.168.1.1
  port 23
!
system
  auth cleartext-pass
  hostname psw0-f5zbr
  password thisisapassword
  output_buffer no
!
channel 1
  name CHANNEL 1
  type toggle
  state high
!
channel 2 {
  name CHANNEL 2
  type toggle
  state low
!
channel 3 {
  name CHANNEL 3
  type toggle
  state high
!
channel 4 {
  name CHANNEL 4
  type no
!
channel 5 {
  name CHANNEL 5
  type nc
!
</code>

===== Hardware Layout =====
==== Pins ====
^ Port ^ Name ^ Assignment ^
| Analog  | A0 | Do not connect (used for random seed) |
| :::     | A1 | Mains voltage |
| :::     | A2 | Battery voltage |
| :::     | A3/17 | Channel 6 |
| :::     | A4/18 | Channel 7 |
| :::     | A5/19 | Channel 8 |
| Digital | 0 | Serial RxD |
| :::     | 1 | Serial TxD |
| :::     | 2 | Unassigned |
| :::     | 3 | Unassigned |
| :::     | 4 | SPI CS SDCard |
| :::     | 5 | Channel 1 |
| :::     | 6 | Channel 2 |
| :::     | 7 | Channel 3 |
| :::     | 8 | Channel 4 |
| :::     | 9 | Channel 5 |
| :::     | 10 | SPI CS Ethernet |
| :::     | 11 | SPI MOSI |
| :::     | 12 | SPI MISO |
| :::     | 13 | SPI SCK  |
| :::     | SDA | Unassigned |
| :::     | SCL | Unassigned |